πŸ“– MANUALCZ | EN

Hob2Hood WiFi – user manual

Smart cooker-hood control linked to an induction hob (Hob2Hood technology), with WiFi control, automatic operation by temperature and humidity, and a clear web interface.

As of firmware version 3.1.01.

Contents
1. What it does Β· 2. First connection Β· 3. Accessing the device Β· 4. Control Β· 5. Hob & remote Β· 6. Manual inputs Β· 7. Automatic mode Β· 8. Run-on Β· 9. Outputs & speeds Β· 10. Display Β· 11. Temperature sensor Β· 12. Cooking history Β· 13. IR codes Β· 14. System Β· 14b. Custom language Β· 15. Firmware update Β· 16. Serial interface Β· 17. Troubleshooting

1. What it does

2. First connection

On first power-up (or until WiFi is configured) the device creates its own network Hob2Hood-Setup. Connect to it with your phone and open 192.168.4.1 (on most phones the setup page opens automatically).

  1. Choose the language at the top.
  2. Select your WiFi network from the list and enter the password. Refresh re-scans the list.
  3. Optionally change the secret settings path and the network name.
  4. Save. The device restarts and connects to your network.

3. Accessing the device

Once connected, open http://hob2hood.local or the IP address the device received (shown on the main page and in your router).

We recommend assigning the device a fixed IP in your router and bookmarking it – it is the most reliable way in if the .local name fails on some phones.

4. Control (main page)

The main page shows the current date and time, temperature and humidity, and the fan and light state. From here you control:

A status line below the buttons shows e.g. "Fan run-on 2:15", "Switched on automatically", or "Manual switch has priority".

5. Hob & remote control

Turning on a cooking zone makes the induction hob send an IR command and the hood sets the speed and light by itself. After cooking the hob sends an off command (see Run-on). Hob2Hood on the hob offers fan speeds 1–4; in the default four-relay wiring speed 4 equals speed 3.

A standard IR remote can be used at the same time. Buttons:

ButtonFunction
+Light on
βˆ’Light off
0Fan off
1 / 2 / 3 / 4Fan speed 1 / 2 / 3 / 4
100+Light and fan off
200+Light on and fan to speed 4
NEXTTurns the light on, then increases fan speed step by step
PREVDecreases fan speed step by step, then turns the light off
CH+ / CHβˆ’Enter and move through the settings parameters (display required)
CHRepeated press changes the value of the shown parameter
PLAY/PAUSEToggles the idle-display mode (parameter 5)
EQToggles whether 0–4 also control the light (parameter 4)
Individual command codes can be changed or learned – see IR codes. The settings menu via the remote works only with a display connected.

6. Manual inputs – switches or buttons

In Settings β†’ Behaviour β†’ Inputs you choose how the physical controls on the hood behave:

ModeBehaviour
SwitchesClosed = on, open = off (classic switches).
ButtonsA press toggles the state; the same button that turned it on also turns it off.

Switch priority

When enabled, the physical control takes priority: while the light (or a speed) is on manually, it cannot be changed from the hob, remote or web – the web buttons grey out. It is released by turning off.

7. Automatic by temperature and humidity

The fan starts by itself based on temperature and humidity and turns off once the values drop by the set hysteresis. For both turning on and off you choose whether both quantities must apply (AND) or either one is enough (OR).

The default is AND / AND: it turns on only when it is both hot and humid (real cooking) and turns off once both fall. Warming the sensor by hand therefore won't start it on the default setting – your hand adds no humidity. To test by hand, switch turn-on to OR.

During automatic operation the display shows the letter A.

Manual off and the automatic mode

When you turn the fan off manually from the web, remote or serial line (and from a switch if switch priority is set), it stays off until temperature and humidity fall below the off threshold – so the automatic mode won't switch it back on under your hands. An off command from the hob does not silence the automatic mode: if it is still hot, it may take over and keep running. Any manual turn-on clears the suppression again.

8. Fan run-on

After the hob's off command the hood keeps running for the set number of minutes (0–60) to clear the remaining steam. Run-on applies only to the hob command – the remote, web, a switch or the serial line turn off immediately. Any action cancels the run-on. The display shows the letter T, and the web counts down the remaining time.

9. Assigning outputs to speeds

The device has 6 outputs: light and V1–V5. For each output V1–V5 you tick the speeds (1–4) at which it switches on. Several outputs can therefore switch at one speed. The default assumes a four-relay module (light + 3 speeds): speed 1 β†’ V1, speed 2 β†’ V2, speed 3 and 4 β†’ V3; outputs V4 and V5 are unused. The assignment can be changed freely.

PWM 0–10 V output

Output V5 can be switched in settings from relay to PWM 0–10 V to drive an external fan through a "PWM β†’ 0–10 V" converter. For each speed (0–4) you enter a duty in percent – for example 0 / 25 / 50 / 75 / 100 %, which on the converter corresponds to roughly 0 / 2.5 / 5 / 7.5 / 10 V. The PWM follows the current speed faithfully, including automatic mode and run-on.

Enabling PWM or changing the pin/frequency applies after a restart; duty changes apply immediately.

10. Display (optional) and LCD menu

An OLED display shows the operating state. It has several parts:

Navigating the menu

The menu is controlled only by the remote and only with a display connected (without a display it is blocked so settings can't be changed blindly). CH+ / CHβˆ’ move between parameters, CH changes the value of the shown parameter. Changes are saved automatically.

#Parameter (on display)MeaningValues
1Fan GraphBottom graphic fan-speed displayOFF Β· N---- Β· N.... Β· ---- Β· .... Β· N
2Time GraphTop graphic time displayOFF Β· 10 / 15 / 30 min Β· 0 min (no scale)
3DisplayMain screen while runningTimer/Β°C Β· Timer Β· Β°C Β· Clock Β· Clock/Β°C
4Fan+Light0–4 also control the light (like EQ)ON Β· OFF
5Screen OFFIdle display with the light offOFF Β· Β°C Β· Clk+Date Β· Clock
6–10Out V1 – Out V5Which speeds switch each output onpattern 1234 / β€œβ€“" (e.g. 1--- = speed 1 only)
11RotationRotate the display 180Β° (after restart)0 Β· 180
12Delay RelayDelay when switching relays0–1000 ms (step 50; mech. relays min. 50)
13Fan Off TimerRun-on after the hob switches off0–60 min
14Switch PrioManual switch priorityON Β· OFF
15Input ModeInput modeSWITCH Β· BUTTON
Parameter names are always in English on the display (international). All of these settings are also in the web interface, where they are translated.

11. Temperature and humidity sensor

At power-up the device detects which sensor is connected:

SensorNote
SHT30 / SHT31 (IΒ²C)Preferred, range up to 125 Β°C – suitable near the hob.
DHT11Cheap, only up to about 50 Β°C.
No sensorWorks; the temperature simply isn't shown and the automatic mode won't start.

12. Cooking history

The "Cooking history" link on the main page shows the last 30 light-on events with date, time and calculated duration, plus a total. It shows how long cooking took. Records are stored in memory and survive a restart (written once the time is synchronised from the internet).

The history page has a field "Log only cooking longer than (min)". Set it to e.g. 3 and shorter light-on events (such as just checking the food) won't be logged at all. 0 stores everything. The field is saved immediately.

13. IR code settings

On a separate page (linked from settings) every IR code from the hob and remote can be changed:

"Restore factory codes" returns the default set.

14. System settings

14b. Custom language (My language)

The interface has five built-in languages (Czech, English, German, Polish, Spanish) and one user slot into which any additional language can be uploaded.

In settings open "Custom language (My language)" and:

After uploading, a "My language" entry appears in the language selector. The translation is stored in the device and survives firmware updates; if a new version adds text, it shows temporarily in English until you download the file again and fill it in. There is one slot – uploading another language overwrites the previous one.

15. Firmware update over WiFi

Upload a new version straight from the browser: in settings open "Firmware update", pick a .bin file and upload. Progress is shown as a percentage; the device restarts when done. Settings, WiFi and IR codes are preserved.

Do not update while cooking – the relays switch off during the upload and the device restarts.

16. Serial interface (for integrators)

Over USB (115200 baud) the device accepts commands and reports temperature/humidity on every change as T:25.4 H:35.

CommandFunction
0–4fan speed (0 = off)
L0 / L1light off / on
RESETclears settings (factory state)
APstarts setup mode

17. Troubleshooting

Web works on IP only, the .local name fails

Restart the device or router. A fixed IP is the most reliable. Some Android phones have trouble with .local in general.

No temperature shown

Check the sensor. No sensor is fine – the device keeps working. The clock appears once time is synchronised.

Factory reset (when nothing else helps)

The device can be returned to factory state without a computer: connect pin GPIO32 to ground (GND) and, keeping it connected, switch the power on. The onboard LED starts blinking (faster in the last three seconds); after 10 seconds all settings, the uploaded custom language and the cooking history are erased and the device restarts to its default state. Release it sooner and nothing happens.

Alternatively, over USB and the serial line (115200) the command RESET does the same.